應急救災大型柴油發電機YT2-150KVA核實機組的真實有用功率。然后確定經濟功率，及備用功率。核定機組真實有用功率的方法為：柴油機12小時額(e)(e)定功率乘以0.9得出一個數據（kw），若發電機額(e)(e)定功率小于或等于該數據，則以發電機額(e)(e)定功率定為該機組真實有用功率，若發電機額(e)(e)定功率大于該數據，則必須用該數據作為機組的真實有用功率。
機房自啟動柴油發電機YT2-150KVA油箱存放位置必須安全以防止火災，油箱或油桶應單獨放在看得見的地方，適當離發電機組遠點，且嚴格規定不準吸煙。油箱內裝的燃油容量應該保證每天的日常供應。油箱放置后，高油面不能比機組底座高出其2.5米，如大油庫油面高于2.5米，應在大油庫與機組之間加日用油箱，使直接送油之壓力不大于2.5米。即使在柴油機關閉期間，不允許燃油依靠重力，通過進油管路或噴油管路流入柴油
醫院應急自啟動柴油發電機YT2-150KVA伊藤柴油機使用壽命、工作可靠性及經濟性在一定程度上取決于柴油機使用初期的磨合。伊藤柴油機磨合期要求切勿超載，伊藤柴油機大功率時工作時間不可超過5min，磨合期每10h應檢查一次曲軸箱的油平面。磨合是延長伊藤柴油機使用壽命的重要起點，磨合期結束后應對新機進行定期維護保養。
120KW機房應急柴油發電機YT2-150KVA伊藤柴油機采用的是PT燃油供給系統。伊藤基本原理是，根據燃油泵輸出的壓力和噴油器進油時間對進油量的影響來控制循環供油量，以滿足柴油機不同工況的需要。因為PT燃油供給系統不配備手油泵，所以需要經常檢查柴油箱里的柴油是否足夠。
進口120KW柴油發電機YT2-150KVA伊藤柴油機在啟動的過程中，為了保護增壓器，在機油壓力表上未顯示出怠速機油壓力前不要加大油門，伊藤柴油機轉速不可高于1000r/min。伊藤柴油機啟動后，特別是在冬季應怠速運轉3～5min，待機油壓力達到0．25MPa后才允許逐步加速；待水溫高于75℃、油溫高于80℃、機油壓力高于0．25MPa時，方可進入全負荷運轉，否則易使增壓器浮動軸承、密封環因缺油而
進口120千瓦發電機YT2-150KVA伊藤柴油機常期在低溫下工作，會使伊藤柴油機低溫腐蝕加重，產生過多的低溫油泥；長期在高溫下工作，會使機油氧化變質加劇、活塞環高溫區結膠現象加重，并產生過多的高溫沉淀（漆膜）。
|
|||
|
|||
 |
